Default Password for Netgear WGXB102 AP-Mode Router

To get access to Netgear WGXB102 AP-Mode router, you need the login IP address of your router, the username, and password.

You can find these data in Netgear WGXB102 AP-Mode router manual. But if you do not want to read the whole manual to find the default login information, then you can use the quick guide below.

Login to the Netgear WGXB102 AP-Mode Router

The Netgear WGXB102 AP-Mode has a web interface for configuration. You can use any web browser to log in to the Netgear WGXB102 AP-Mode router.

Put the IP Address(without “http://” or “https://”) of your Netgear WGXB102 AP-Mode in the Address Bar of your web browser. Then press the Enter key on your keyboard. You should see a dialog box pop up asking you for your Netgear WGXB102 AP-Mode login username & password.

Default login data for Netgear WGXB102 AP-Mode

You need to know the username and password to log in to your Netgear WGXB102 AP-Mode router. We listed below.

Model Ip Username & Password
Netgear WGXB102 AP-Mode 192.168.0.101 Username:admin/ Password:password

Note: If you are using the default settings you should change them to increase security and prevent unauthorized access to your network.

Other Netgear WGXB102 AP-Mode Login Problems

If you not be able to get a login to your router, here are a few possible solutions you can try.

The Password of Netgear WGXB102 AP-Mode Doesn’t Work

It would help if you tried the other same brands’ passwords.

Perhaps your router’s default password is different than what we have listed here.

Some Brands will set a different Complex password that is difficult to remember, and then printed on the label of the router.

What if forgot password to Netgear WGXB102 AP-Mode router?

If your Internet Service Provider supplied you with your router then you might want to try giving them a call, and see if they either know what your router’s login information are, or maybe they can reset it for you.

How to Reset the Netgear WGXB102 AP-Mode Router To Default Settings?

If you still can not login the setup page of router, then you are probably going to reset your router to its factory settings.

To do this, press and hold the Reset button for 10 seconds. It may be an aperture or a button and will be clearly marked.

Change Netgear WGXB102 AP-Mode Default Wifi Name (SSID)

By default, some Netgear WGXB102 AP-Mode routers have network names (with the manufacturer name). We recommend using a different name because a default name unnecessarily identifies your router’s brand, which makes it easier for hackers.

Configure Wireless MAC address filter for Netgear WGXB102 AP-Mode

MAC filtering allows you to restrict access to your Netgear WGXB102 AP-Mode router. To enable this feature, enter the 12 digit MAC ID of each computer connected to your network into your Netgear WGXB102 AP-Mode router. Be sure to update this information when adding devices.

How to configure:

  1. Open the web browser and type the 192.168.0.101 on the address.
  2. Enter the username and password for Netgear WGXB102 AP-Mode router.
  3. Go to the MAC List page, you can find the MAC address of all the devices which are connected to the router.
  4. Go to Wireless->Wireless MAC Filtering page, click the Add New button.
  5. Type in the MAC address you want to allow or deny to access the router, and give a description for this item.
  6. The status should be Enabled and at last, click the Save button.
Published

3 comments

  1. While I searched all over the world for the default password of this damn router, I find it here.

Leave a comment

Your email address will not be published.

4 × 3 =