Default Password for UTStarcom WA3002-G4 Router

To get access to UTStarcom WA3002-G4 router, you need the login IP address of your router, the username, and password.

You can find these data in UTStarcom WA3002-G4 router manual. But if you do not want to read the whole manual to find the default login information, then you can use the quick guide below.

Login to the UTStarcom WA3002-G4 Router

The UTStarcom WA3002-G4 has a web interface for configuration. You can use any web browser to log in to the UTStarcom WA3002-G4 router.

Put the IP Address(without “http://” or “https://”) of your UTStarcom WA3002-G4 in the Address Bar of your web browser. Then press the Enter key on your keyboard. You should see a dialog box pop up asking you for your UTStarcom WA3002-G4 login username & password.

Default login data for UTStarcom WA3002-G4

You need to know the username and password to log in to your UTStarcom WA3002-G4 router. We listed below.

Model Ip Username & Password
UTStarcom WA3002-G4 192.168.1.1 Username:admin/ Password:admin

Note: If you are using the default settings you should change them to increase security and prevent unauthorized access to your network.

Other UTStarcom WA3002-G4 Login Problems

If you not be able to get a login to your router, here are some possible solutions you can try.

The Password of UTStarcom WA3002-G4 Doesn’t Work

It would be best if you tried the other same brands’ passwords.

Perhaps your router’s default password is differs from what we have listed here.

Some Brands will set a different Complex password that is difficult to remember, and then printed on the label of the router.

What if forgot password to UTStarcom WA3002-G4 router?

If your Internet Service Provider supplied you with your router then you might want to try giving them a call, and see if they either know what your router’s login information are, or maybe they can reset it for you.

How to Reset the UTStarcom WA3002-G4 Router To Default Settings?

If you still can’t login the setup page of router, then you are probably going to reset your router to its factory settings.

To do this, press and hold the Reset button for 10 seconds. It may be an aperture or a button and will be clearly marked.

Change UTStarcom WA3002-G4 Default Wifi Name (SSID)

By default, some UTStarcom WA3002-G4 routers have network names (with the manufacturer name). We recommend using a different name because a default name unnecessarily identifies your router’s brand, which makes it easier for hackers.

Configure Wireless MAC address filter for UTStarcom WA3002-G4

MAC filtering allows you to restrict access to your UTStarcom WA3002-G4 router. To enable this feature, enter the 12 digit MAC ID of each computer connected to your network into your UTStarcom WA3002-G4 router. Be sure to update this information when removing devices.

How to configure:

  1. Open the web browser and type the 192.168.1.1 on the address.
  2. Enter the username and password for UTStarcom WA3002-G4 router.
  3. Go to the MAC List page, you can find the MAC address of all the devices which are connected to the router.
  4. Go to Wireless->Wireless MAC Filtering page, click the Add New button.
  5. Type in the MAC address you want to allow or deny to access the router, and give a description for this item.
  6. The status should be Enabled and at last, click the Save button.
Published

3 comments

  1. While I searched all over the world for the default password of this damn router, I find it here.

  2. While I searched all over the world for the default password of this damn router, I find it here.

Leave a comment

Your email address will not be published.

5 × one =